Skip to main content

How to Move a Washing Machine Safely: Disconnect, Drain and Transport It Without Damage

How to Move a Washing Machine Safely: Disconnect, Drain and Transport It Without Damage

A washing machine looks like a solid box, but inside is a heavy drum on springs, with water hiding in hoses, the pump, and the filter. Move it unprepared, and you can flood a floor or end up with a machine that shakes and leaks.

A hand placing colourful towels into a front-loading washing machine
Illustrative photo: a front-loading washing machine in everyday use. Photo by Towfiqu barbhuiya on Pexels (Photo ID 11852050). View the photo on Pexels.

Most of that damage is preventable. Empty the drum, drain the water, lock the drum in place, and keep the machine upright. Do the preparation the day before moving day.

Why washing machines get damaged in a move

Three things cause most problems. The drum hangs on suspension parts, so an unlocked drum can swing and hit the casing on a bumpy road. Water stays in the hoses, pump, and filter after a wash, and spills out when tilted.

Check your manual first, as steps vary by model. If the plumbing looks old, ask a plumber for help rather than forcing a valve.

What you will need

  • Transit bolts for your model, plus the spanner that fits them
  • A bucket, a shallow tray, and plenty of old towels
  • Pliers, painter’s tape, and a moving blanket or old duvet
  • An appliance dolly, moving straps, a second person, and a spirit level

Step 1: Empty the drum and find the transit bolts

Take everything out of the drum and run a short rinse and spin cycle with the machine empty. This pumps out most of the water in the hoses and pump. Wipe the rubber seal dry and leave the door slightly open overnight.

Now find the transit bolts. Most front-load machines arrived with three or four long bolts in the back panel, removed at installation. They are often kept with the manual. If you cannot find them, buy a universal kit that fits your model.

Step 2: Turn off the water and disconnect the hoses

Turn off the water first; the shut-off tap is usually behind the machine or under a nearby sink. Then unplug the machine, pulling the plug, not the cable. With the bucket ready, unscrew the inlet hose from the tap and the machine, holding the end over the bucket. Lower the drain hose in too.

Step 3: Drain the pump filter

Even after the hoses are empty, water stays in the pump and filter. The filter cover is usually a small flap at the bottom front. Put the tray in front of it and open it slowly. If your model has a small emergency drain hose beside the filter, use it. If not, ease the filter out a little at a time, then clear out lint or coins and put it back.

Step 4: Lock the drum and secure the loose parts

For a front-load machine, screw the transit bolts into the holes in the back panel and tighten them firmly, without over-tightening. Keep the plastic plugs safe for the new home. Most top-load machines have no transit bolts: follow the manual and tape the lid shut.

Coil the power cable and tape it to the back of the machine. Tape the hoses to the back as well, or put them inside the drum. Close the door and tape it lightly shut. Never lift the machine by its door, lid, or control panel.

Step 5: Wrap it and move it upright with two people

Wrap the machine in a moving blanket or an old duvet and tape it in place. Before you lift anything, walk the route to the van, measure doorways and turns, and clear the path of rugs and cables.

Move it with two people and an appliance dolly, lifting from the base. On stairs, go one step at a time, with one person above and one below. Keep it upright: makers advise against laying it on its side, as leftover water can leak where it should not. If you tilt it through a doorway, stand it upright again and let it rest before switching it on.

Step 6: Load, strap, and set it up again

Load the machine upright against a wall of the van and strap it firmly, so it cannot slide or tip. Do not stack anything on top of it. On arrival, unload it the same way, straight to its new spot.

Level the machine with the spirit level, turning the feet until the bubble sits in the middle, then tighten the locking nuts. Then remove the transit bolts before you plug it in or run a wash: running it with the bolts in will make it shake and bang and can damage it. Keep the bolts safe and cover the holes with the plugs.

Reconnect the hoses, then check for leaks. Turn the water on slowly and run a short empty rinse and spin cycle. Look behind and underneath for drips. If a connection drips, tighten the fitting and check again. If it still leaks, switch it off and ask a plumber.

Mistakes to avoid

  • Moving a front-load machine without fitting the transit bolts.
  • Skipping the pump filter drain, so leftover water spills when the machine is tilted.
  • Laying the machine on its side, or carrying it alone.
  • Forgetting to remove the transit bolts before the first wash.
  • Reconnecting the hoses in a rush and not checking for leaks first.

When to ask for help

Do it yourself only if you have a helper, a dolly, the transit bolts, and a clear route to the van. Ask your mover or a plumber if the machine is built in, the hoses look damaged, or the stairs are narrow or steep.

Frequently asked questions

Do I really need transit bolts to move a washing machine?

For a front-load machine, yes. The bolts lock the drum so it cannot swing and strain its suspension on the road.

Can I lay a washing machine on its side to fit it in a van?

Keep it upright if you can. Makers advise against laying it down, as water left inside can leak into parts it should not reach.

How do I drain a washing machine before moving it?

Run an empty rinse and spin, turn off the water and unplug the machine, disconnect the hoses over a bucket, then drain the pump filter over a tray.

What happens if I run a wash with the transit bolts still in?

The machine will shake and bang, as the drum cannot move as it should. Switch it off, unplug it, and remove the bolts before running it again.

My washing machine shakes after the move. What should I check?

Check that the transit bolts are out and the machine is level, with all four feet on the floor. Then run an empty test cycle and check for leaks.

Moving a washing machine is mostly preparation: drain it, lock the drum, keep it upright, and set it up slowly at the new home.

Comments

Popular posts from this blog

How to Pack Fragile Items for Moving Without Breaking Them

How to Pack Fragile Items for Moving Without Breaking Them Most moving-day breakages do not happen because an item was dropped from a great height. They happen because a plate was stacked flat under a heavy pile, a glass was left loose in a half-empty box, or a mirror was carried without corner protection. This guide covers a careful method, item by item, for dishes, glasses, mirrors, and electronics. Photo by RDNE Stock project on Pexels. Illustrative image of a moving box marked fragile. The core idea is simple: every fragile item gets its own wrapping, every box gets cushioning at the bottom, sides, and top, and nothing inside the box is allowed to move. If you shake a sealed box gently and feel items shifting, it needs more padding. Pack fragile items early and keep them in one marked area, so they are loaded last and unloaded first. Five Golden Rules of Fragile Packing Wrap each item separately. Two unwrapped plates rubbing together can chip each other. Use packing paper...

How to Move a Sofa Through a Narrow Doorway Without Damaging It

How to Move a Sofa Through a Narrow Doorway Without Damaging It A sofa that sailed into your living room years ago can suddenly seem impossible to get out. It wedges in the doorway and will not turn in the hallway. The problem is usually the angle, the legs, and the door still hanging on its hinges. With a tape measure, a little disassembly, and the right pivot, you can usually get it through unscratched. Photo by RDNE Stock project on Pexels. Illustrative image of a sofa being carried through a hallway. It is not a photo of the author's own move. Why Sofas Get Stuck in Doorways A sofa is wide, deep, and awkward all at once, and a doorway only gives you width and height to work with. Carried flat, the sofa's depth usually jams first. The trick is to find the position where the sofa's smallest profile faces the narrowest part of the opening. One measurement matters most: the diagonal depth, from one bottom corner of the frame to the opposite top corner of the arm. If...